TufTruck TTC-1225 Ram rear coils installed

Eastern Nevada

At the SEMA Show a few years ago TUFTRUCK introduced heavy-duty rear springs for the 2014 and newer Ram 2500 trucks. They had already been making replacement coils for the front axles of Ram trucks and other brands for several years.

TUFTRUCK is a brand of McAllister Industries out of British Columbia, Canada. This company has over 100 years of manufacturing experience, making leaf and coil springs for everything from light trucks up to huge mining equipment from quality American steel.

The TTC–1225 springs fit the 2014-and-newer, Ram 2500 trucks with coils atop the rear axle and cost about $425 a pair. They have a spring rate of 438 pounds-per-inch, and according to TUFTRUCK they add an additional 500 pounds of capacity. The chart below tells how much beefier the TUFTRUCK coils are compared to the stockers, and the differences are easy too see, feel, and measure.

Beefy Canadian aftermarket heavy-duty replacement rear coil springs.

 

TTC-1225 vs OE Coil TUFTRUCK TTC-1225 OEM 2014 Rear Coil
Height 18” 17.75”
Diameter 8” 7.5”
Material Thickness 0.93” 0.86”
Weight 35-lb 24-lb

 

Left: TTC-1225 Right: OEM Ram 2500 rear coil.

Installation And Road Tests

Swapping the rear coils on heavy-duty Rams is a simple job for the mechanically inclined and experienced; it is much easier than removing and replacing long, heavy, and awkward leaf packs. I did the project by myself, without a vehicle hoist and with zero cursing. If I had been removing-and-replacing leaf springs, particularly solo, there certainly would have been busted knuckles and profanity.

Ran this setup for many thousands of miles on two 2500 trucks; OE coils and Air Lift 1000 springs.

After chocking the tires on the front axle, lifting the rear of the truck, supporting the frame with jack stands, disconnecting the rear shocks and body-roll bar, and removing the rear wheels, the axle was drooped as far as practical to make the coils loose enough to remove. (Remember to insure you’re not pulling on brake or ABS lines.) Because the TUFTRUCK coils were just fractionally taller, and drooping the axle provided plenty of access, no spring compressor was needed. I spent much more time making measurements, videos, and photographs than doing mechanical work.

Doing the spring R&R was incredibly easy.

To make a direct, back-to-back comparison of the factory coils and the TUFTRUCK TTC-1225, the Air Lift auxiliary springs were deflated (to zero) before I drove a 15-mile test loop over a mix of city streets, rural highways, and interstate freeway. This type of repeatable initial testing, combined with notes made during the drive, helped document performance differences with an eye on reducing the effects of faded memories and subjectivity.

After installing the TTC–1225, there was a noticeable and substantial improvement in stability, control, and spring rate compared to the OEM coils. The stouter and fractionally taller TTC-1225 coils produced a 3/4” height increase measured at the bottom of the hitch receiver, with my Hallmark camper mounted (without water or gear).

TUFTRUCK’S TTC-1225 rear coils installed and ready for work.

Shortly after the installation I made a 1,000 mile roundtrip over the north-south length of Nevada, to buy a new Welsh Terrier puppy, our first travel-size dog. Then a 1,500-mile round trip to the Southwest in May. The TUFTRUCK rear springs are working well, and I’m glad I added them. Stay tuned, there are additional rear suspension upgrade editorials coming.

Our new six-month-old Welsh Terrier puppy we named Elsie Desert Rose. She fits well atop the center console in the regular cab camper truck.

Tell ’em you saw it on RoadTraveler.net

Become a RoadTraveler patron. Thanks!

James Langan

Copyright James Langan/RoadTraveler. All Rights Reserved

Resource:

tuftruck.com

 

Auxiliary Springs

2017 Ram 2500 with Hallmark Nevada Flatbed Camper

Truck Camper Suspension Q & A

The questions and answers below were prompted by recent posts regarding auxiliary springs for my truck camper outfit.

Backgrounder

Iggy The Igloo asked about heavy-duty suspension setup and options. Iggy has a Fourth Generation Ram 3500 crew cab, long bed, with a flatbed Alaskan popup. His truck had Firestone air springs, including Daystar cradles to prevent limiting droop-travel, but he did not like how the airbags consumed inches of up-travel. His front axle has Thuren Fab 1.5-inch replacement coils.

Questions, Answers, and Comments

Q] Do you leave your camper mounted full-time?

A] The chassis is always loaded with my Hallmark flatbed camper, tools, and gear. I will remove the Hallmark occasionally to inspect things, but have not done so yet.

2014-and-newer Ram 2500s (like mine) have coils in the rear, so I couldn’t install extra leaf springs (add-a-leaf). My assessment from owning two coil-sprung, late-model Ram 2500s is that the OE rear coils work surprisingly well, even with maximum loads. However, for a big camper it seems nearly everyone (2500 & 3500, F250 & F350) wants or needs additional spring-rate for better all-around performance. Regardless of whether one uses air, rubber, or metal auxiliary springs, the goal is to support the load.

Excessive rear-overhang and tail-swing is popular these days… most of the camper is behind the rear axle. This nice FWC flatbed on a Ram 3500 was at Overland Expo West 2019.
F-350/3500 pickups are arguably superior to F-250/2500 series trucks for maximum loads, yet this Ram 3500 with a massive aftermarket rear leaf-spring pack still employs auxiliary air springs for support.

If new or additional springs were not desirable for big weight, then those who rarely fill their trucks to capacity would complain loudly about heavy-duty pickup ride-quality. New trucks generally offer a more comfortable and softer ride these days, both with and without a load, though sometimes this includes compromises for heavy-hauling.

These good Old Man Emu/ARB Dakar springs were obviously flattened by a FWC Raven slide-in camper on a 2011 Toyota Tundra. Auxiliary support was added.

Replacement springs? Add-ons? Both?

Q] Why did you choose Timbren springs instead of an add-a-leaf?

A] My 2017 Ram 2500 uses something similar to an add-a-leaf in the form of beefier aftermarket rear coils from TufTruck. They were helpful, though they’re only designed for an additional 500-pounds. This is not enough, and I’m trying to convince TufTruck to make new coils with substantially more capacity.

TufTruck TTC-1225 replacement Ram 2500 rear coil springs.

The latest single-convoluted Timbrens and my other modifications (aftermarket sway/body-roll bars, shocks, and stout tires) have helped my flatbed outfit drive and handle impressively well for its size, weight, and height.

Aftermarket air springs seem to be the most common heavy-duty suspension upgrade, likely due to their cost, adjustability, and ease of installation. I’ve used air before, though some negatives can include leaks, failure in extreme cold temperatures, and a bouncy ride. Some choose replacement leaf packs, but if the weight is removed the extreme-duty replacements can be too stiff for an unladen truck.

Butt Sag

Q] How have your Timbrens changed the sag? Did the springs put you back up to stock ride height with your load, or do you still have some sag?

A] Neither my 2014 crew cab, which used to carry a Hallmark slide-in, nor my 2017 regular cab flatbed, has ever had a sagging, negative-rake stance. This was largely because I didn’t lift or level the front first. This is the opposite approach of many these days.

For my ’17 Ram 2500, I added the Hallmark Nevada flatbed, gear and other heavy accessories, while experimenting with auxiliary rear suspension options. Lighter-duty Air Lift 1000 springs inside the rear coils were used initially, then TufTruck replacement springs, and now the rubber Timbrens.

Butt low, negative rake stance was avoided by sorting rear load support first. This is after adding TufTruck TTC-1224 HD front (lift) springs.

While I respect companies like Thuren Fab and think their products are great, their parts are focused on a softer ride and/or going fast over rough terrain. Softer springs don’t add load support, and that’s typically the wrong direction for heavy, overland-style, backcountry camper outfits. There are numerous examples online of folks choosing to use softer go-fast springs (particularly on the rear axle) who after installation needed them to be reengineered or replaced because they were inappropriate for their load.

To their credit, I called and talked to Thuren Fab several months ago when shopping for front coils; I shared my measured axle weights and application specifics. They were direct and honest, stating that their front springs would not give the listed lift due to the weight on my front axle (winch bumper, camper, etc.), and they did not try to talk me out of using the higher-rate TufTrucks I was considering. They agreed that firmer springs were a good idea. As mentioned above, in many cases I think the rear springs from the go-faster companies are even less desirable than the fronts for heavy-duty applications; they’re not intended for the load support that heavy outfits need.

Only using products that added spring rate to the rear suspension helped me retain some of the factory-positive rake with my camper. I dislike a butt-low, negative rake. The front remained lower than the rear until I changed the front springs.

TufTruck’s heavy-duty front coils were installed May 2019. The TufTruck TTC-1224 gave me about 2.75-inches of lift, essentially leveling the chassis. Since adding the TTC-1224 I have been playing with the ride height, keeping the chassis either slightly higher in the rear, or level, depending on how I choose to adjust the rear suspension.

TufTruck TTC-1224 HD front coils for Ram 2500/3500s were installed above the front axle, providing both load support and inches of lift.

Compression Travel Loses?

Q] Do you think the Timbren’s inhibit your up-travel more than an add-a-leaf?

A] I have not tried to measure or document up-travel loses; supporting the load and overall handing has been the priority, while not limiting droop-travel. Coil-sprung axles have inherently better droop-travel, but they are generally inferior to leaf springs at controlling body-roll.

Air Lift plastic spring spacer (for lifted rear) droop-travel failure on 2011 Toyota Tundra. This prompted me to use Timbren rubber springs instead of traditional air springs for the FWC load.

In addition to firmer springs, my aftermarket heavy-duty sway/roll-bars limit travel; their performance benefits far outweigh any losses. While I enjoy superior off-pavement performance, I’m realistic about my outfit’s capabilities in the dirt. An empty full-size pickup can do much more, easily and safely, than one with a higher center-of-gravity that’s carrying tons of payload.

As an aside, I am not critical of your adding lift/leveling blocks in the rear. Near the end of my 2011 Tundra project with a Four Wheel Campers slide-in, I placed two-inch blocks under the rear springs and it was fine, loaded and not. Taller or different blocks don’t always cause axle-wrap or other problems.

Small, two-inch block added to the rear of a 2011 Tundra. There was not one before.

Tell ‘em you saw it on RoadTraveler.net.

James Langan

Copyright James Langan/RoadTraveler. All Rights Reserved

Resources:

Air Lift Performance

Four Wheel Campers

Hallmark Truck Campers

Thuren Fab

Timbren

TufTruck

 

 

TUFTRUCK Heavy Duty Dodge Ram Front Coil Springs

First-look:
TUFTRUCK TTC-1224 Heavy-Duty Front Coil Springs.

 

James Langan

Copyright James Langan/RoadTraveler All Rights Reserved

Resource: TUFTRUCK